RAILFX 102 WOOD/MET 1/8" CABLE RAIL KIT OUT/OUT LEV

Description

Quality tested
Order Tracking
Fast Shipping
Exterior Upgrades
Get the look you deserve and dress up your homes astetic with these easy to use product
RAILFX 102 WOOD/MET 1/8" CABLE RAIL KIT OUT/OUT LEV
A through-the-post configuration is the ideal scenario to use the Basic threaded stud kits. The threaded studs are a functional fitting, not a hide-in-the-post solution. A brass hex nut and some metal thread (both covered by an end cap) will extend beyond the back of the post on one end. A Pull-Lock
®
fitting is installed through the other end.
For either wood or metal posts, use the 102 Basic Series. The tensioning device is a 2-7/8” long threaded stud which installs on the back side of one end post.
When taking cable railing through a corner, do not bend the cable past 45
⁰
at any one time. If turning 90
⁰
, a 2-step turn using a double corner post configuration is required.
The Basic 102 Series kit is offered with cable lengths from 5′-70′.  Each kit contains the cable and hardware needed to complete one run.
Tools Required for Installation
• 5/32″ Drill Bit
• 1/4″ Drill Bit
• 29/64″ Drill Bit
• 1/8″ Hex Wrench
• 7/16″ Wrench
• RFXPL-KEY
• Cut Off Kit (mandrel)
• Cut Off Kit (wheel)
Features
For wood or metal posts
Easy to install with specific pre-cut lengths that can be trimmed to a finished dimension in the field
Made from corrosion resistant, high-strength type 316 stainless steel
Pull-lock system makes installation fast and easy
Cable assemblies have a 2-7/8" long threaded stud which installs on the backside of one end post
Fittings at both ends completely concealed in post which protects the fitting and provides a cleaner appearance
Can be drilled level into wood or metal, even on stairs or radius. No angle drilling or beveled washer needed on end posts
Tensioning nut is made from brass which prevents thread lock
Suitable for indoor or outdoor enjoyment
Includes stainless steel cap for non-tensioning end. (End cap for tensioning end included.)
Payment
Shipping
Payment
Shipping
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
Your order will be dispatched (Monday-Friday) and you should expect to receive it three to four days after dispatch.
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
THANK YOU
A through-the-post configuration is the ideal scenario to use the Basic threaded stud kits. The threaded studs are a functional fitting, not a hide-in-the-post solution. A brass hex nut and some metal thread (both covered by an end cap) will extend beyond the back of the post on one end. A Pull-Lock® fitting is installed through the other end. For either wood or metal posts, use the 102 Basic Series. The tensioning device is a 2-7/8” long threaded stud which installs on the back side of one end post. When taking cable railing through a corner, do not bend the cable past 45⁰ at any one time. If turning 90⁰, a 2-step turn using a double corner post configuration is required. The Basic 102 Series kit is offered with cable lengths from 5′-70′. Each kit contains the cable and hardware needed to complete one run. Tools Required for Installation • 5/32″ Drill Bit • 1/4″ Drill Bit • 29/64″ Drill Bit • 1/8″ Hex Wrench • 7/16″ Wrench • RFXPL-KEY • Cut Off Kit (mandrel) • Cut Off Kit (wheel) Features ---For wood or metal posts ---Easy to install with specific pre-cut lengths that can be trimmed to a finished dimension in the field ---Made from corrosion resistant, high-strength type 316 stainless steel ---Pull-lock system makes installation fast and easy ---Cable assemblies have a 2-7/8" long threaded stud which installs on the backside of one end post ---Fittings at both ends completely concealed in post which protects the fitting and provides a cleaner appearance ---Can be drilled level into wood or metal, even on stairs or radius. No angle drilling or beveled washer needed on end posts ---Tensioning nut is made from brass which prevents thread lock ---Suitable for indoor or outdoor enjoyment ---Includes stainless steel cap for non-tensioning end. (End cap for tensioning end included.)
Quality tested
Order Tracking
Fast Shipping
Exterior Upgrades
Get the look you deserve and dress up your homes astetic with these easy to use product
RAILFX 102 WOOD/MET 1/8" CABLE RAIL KIT OUT/OUT LEV
A through-the-post configuration is the ideal scenario to use the Basic threaded stud kits. The threaded studs are a functional fitting, not a hide-in-the-post solution. A brass hex nut and some metal thread (both covered by an end cap) will extend beyond the back of the post on one end. A Pull-Lock
®
fitting is installed through the other end.
For either wood or metal posts, use the 102 Basic Series. The tensioning device is a 2-7/8” long threaded stud which installs on the back side of one end post.
When taking cable railing through a corner, do not bend the cable past 45
⁰
at any one time. If turning 90
⁰
, a 2-step turn using a double corner post configuration is required.
The Basic 102 Series kit is offered with cable lengths from 5′-70′.  Each kit contains the cable and hardware needed to complete one run.
Tools Required for Installation
• 5/32″ Drill Bit
• 1/4″ Drill Bit
• 29/64″ Drill Bit
• 1/8″ Hex Wrench
• 7/16″ Wrench
• RFXPL-KEY
• Cut Off Kit (mandrel)
• Cut Off Kit (wheel)
Features
For wood or metal posts
Easy to install with specific pre-cut lengths that can be trimmed to a finished dimension in the field
Made from corrosion resistant, high-strength type 316 stainless steel
Pull-lock system makes installation fast and easy
Cable assemblies have a 2-7/8" long threaded stud which installs on the backside of one end post
Fittings at both ends completely concealed in post which protects the fitting and provides a cleaner appearance
Can be drilled level into wood or metal, even on stairs or radius. No angle drilling or beveled washer needed on end posts
Tensioning nut is made from brass which prevents thread lock
Suitable for indoor or outdoor enjoyment
Includes stainless steel cap for non-tensioning end. (End cap for tensioning end included.)
Payment
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
Shipping
Your order will be dispatched (Monday-Friday) and you should expect to receive it three to four days after dispatch.
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
THANK YOU
A through-the-post configuration is the ideal scenario to use the Basic threaded stud kits. The threaded studs are a functional fitting, not a hide-in-the-post solution. A brass hex nut and some metal thread (both covered by an end cap) will extend beyond the back of the post on one end. A Pull-Lock
®
fitting is installed through the other end.
For either wood or metal posts, use the 102 Basic Series. The tensioning device is a 2-7/8” long threaded stud which installs on the back side of one end post.
When taking cable railing through a corner, do not bend the cable past 45
⁰
at any one time. If turning 90
⁰
, a 2-step turn using a double corner post configuration is required.
The Basic 102 Series kit is offered with cable lengths from 5′-70′.  Each kit contains the cable and hardware needed to complete one run.
Tools Required for Installation
• 5/32″ Drill Bit
• 1/4″ Drill Bit
• 29/64″ Drill Bit
• 1/8″ Hex Wrench
• 7/16″ Wrench
• RFXPL-KEY
• Cut Off Kit (mandrel)
• Cut Off Kit (wheel)
Features
For wood or metal posts
Easy to install with specific pre-cut lengths that can be trimmed to a finished dimension in the field
Made from corrosion resistant, high-strength type 316 stainless steel
Pull-lock system makes installation fast and easy
Cable assemblies have a 2-7/8" long threaded stud which installs on the backside of one end post
Fittings at both ends completely concealed in post which protects the fitting and provides a cleaner appearance
Can be drilled level into wood or metal, even on stairs or radius. No angle drilling or beveled washer needed on end posts
Tensioning nut is made from brass which prevents thread lock
Suitable for indoor or outdoor enjoyment
Includes stainless steel cap for non-tensioning end. (End cap for tensioning end included.)